Pregnancy Belly Casting Kit by Proud Body

Pregnancy Belly Casting Tips

How to make a pregnancy belly cast including your hands

Some moms like to include the hands of a loved one in their pregnancy belly cast. It is very easy to do. Just put the hands right on the belly, apply the Vaseline over the back of the hands as you are coating the rest of the mom's casting area, and then simply cast right over the hands. Make sure the fingers are spread far enough apart so that it is easily distinguishable that it is a hand being cast into the pregnancy belly cast.

How to get a really smooth pregnancy belly cast

A tip to make a really smooth cast is to dip your fingers in water after you apply a couple of overlapping layers of the plaster casting strips and rub your fingers over the layers to mix the plaster of paris together among the layers. Work fairly quickly as the plaster strips will begin to dry within a few minutes after you begin applying the plaster strips. After your pregnancy belly cast has completely dried, lightly sand it with the sanding screen included in our kit. If you still want an even smoother surface, apply 1-2 layers of Gesso (acrylic priming paint) and let dry according to the manufacturer's instructions.

A more advanced method of making a smoother cast is to apply a thin layer of joint compound or spackle which can be found at your local home improvement store. Apply it with your fingers and as it starts to dry, smooth it out more with your fingers. Allow it to dry according to the manufacturer's instructions and then lightly sand it using our sanding screen. You may need to apply more than 1 layer of joint compound or spackle, allowing each layer to dry and lightly sanding in between each coat.


How to support your breasts during the casting

Since pregnancy belly casting is typically done with the mom unclothed from below the belly up, a common question we get asked is "just how can my breasts have some support while I'm doing the casting?" There are a few different ways to give your breasts some support during the casting:

1. My favorite is to take a long piece of saran wrap, fold it in half and wrap it around your body beginning under your breasts where your bra strap would usually rest. Continue to wrap the saran wrap around your body working your way up under your breasts until you have the amount of support you desire;

2. wear a strapless bra, but the fabric and seams will show through your cast, and don't wear your favorite bra because between the Vaseline and the casting material, even after washing it will probably never be the same again; or

3. buy those disposable "pasty" bras that are available at your local department store.


How to include your thighs in the casting

To have your pregnancy belly cast look right, you will need to do your casting while standing. Start the casting from the top and work your way down. When you get to the bottom of your belly, place a piece of saran wrap over your pubic area to keep the wet casting material from sticking to it. Slather the saran wrap with Vaseline prior to placing it over your pubic area. You will need to hold the saran wrap in place while your helper places the first wet strip over the pubic area. Thereafter, the wet casting strips will hold the saran wrap in place.

Alternatively, you can wear a pair of panties. Try to wear a more delicate pair since the seams won't show as much. Then tuck the saran wrap into the seams to hold it in place.


Vaseline removal from the inside of your pregnancy belly cast

You might wonder just how to get the excess Vaseline out of the inside of your cast. If you're a patient person (and I wasn't when I made mine!), the Vaseline will eventually dry out. If you want quicker results, first take a dry paper towel and wipe out any excess. Then, take another paper towel and dip it in rubbing alcohol and gently dab it on the Vaseline to dissolve it. Just be careful not to apply so much rubbing alcohol that it saturates your pregnancy belly cast.


Smoothing the edges of your pregnancy belly cast

Don't worry about having the edges of your pregnancy belly cast be even as you are making the cast. After your pregnancy belly cast has completely dried, you can take a pair of sharp scissors and trim the edges to make them even if you like.


Reinforcing thin areas of your pregnancy belly cast

If you have casting material left over, you can reinforce the cast where needed. Simply wet additional casting strips and place them on the inside of your belly cast where reinforcements are needed. If you have run out of casting strips, you can order additional rolls to make your reinforcements.

Here's a tip submitted from one of our customers--they bought a body repair kit from an auto parts store. "The kit comes w/ glass cloth and epoxy resin. We applied it to the inside of the cast and brushed a light coat of resin on the outside. Then sanded, primed and painted. The cast is so incredibly durable now!! We recommend that anyone who's cast feels flimsy due to not putting enough layers on in certain sections (as was the problem with ours) to do this easy technique."